CorporateGolfXtra 2024
+ Reply to Thread
Results 1 to 20 of 20
  1. #1
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315

    anyone have a big saw able to cut an 8x8" piece of wood?

    I'm making a table and need to cut some pieces of douglas fir that are just under 8x8". I can do it with a couple of cuts on my mitre saw but was wondering if anyone had a bigger saw at home that would do this (e.g. radial arm saw), etc.

    thanks
    I got a fever. And the only prescription is more golf equipment.

  2. #2
    Postmaster General big mac is on a distinguished road big mac's Avatar
    Join Date
    Feb 2004
    Location
    Home-and glad to be
    Posts
    3,821
    Jeff---are you crosscutting or ripping ? Bandsaw will do if you find a big one. Pretty hard to crosscut as the throat on most saws are 14 or 20 inches. If your ripping then anyone with a portable bandsaw mill can do it.

    Ever tried to use a handsaw ?? A good sharp one will work
    Does the 2nd hole-n-one come easier ?

  3. #3
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    I am cross cutting it. I need the cut to be pretty exact and want to do minimal sanding. Don't want to do it by hand for accuracy reasons and the number of cuts required.
    I got a fever. And the only prescription is more golf equipment.

  4. #4
    Golf Guru justsomeguy is on a distinguished road
    Join Date
    Nov 2007
    Location
    around here
    Posts
    2,117
    Quote Originally Posted by jeffc View Post
    I am cross cutting it. I need the cut to be pretty exact and want to do minimal sanding. Don't want to do it by hand for accuracy reasons and the number of cuts required.
    My advice is to take it to Home Depot or Rona and have them cut it for you. They'll charge you $X/cut, but they have the right equipment and you'll be sure to get what you want.

  5. #5
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    Quote Originally Posted by justsomeguy View Post
    My advice is to take it to Home Depot or Rona and have them cut it for you. They'll charge you $X/cut, but they have the right equipment and you'll be sure to get what you want.
    yes, but will the cut it if i didn't buy it there? i would buy it there but they don't carry it
    I got a fever. And the only prescription is more golf equipment.

  6. #6
    Singles Match Play Champ 2011 John is on a distinguished road John's Avatar
    Join Date
    Nov 2002
    Location
    Ottawa
    Posts
    6,202
    They will definitely do the cuts for you even if you didn't buy it there Jeff, i do it all the time. Don't waste your time at HD either go to Rona, the Cut Shop is far superior. Let's see some pics of this sucker once completed!

  7. #7
    Gotta Post Break68 is on a distinguished road Break68's Avatar
    Join Date
    May 2009
    Location
    Vancouver
    Posts
    2,257
    Rona has a huge table saw, they are much better in their cut shop then Home Depot.
    Rona all the way for cuts.
    Obviously you're not a golfer.

  8. #8
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    so no luck with Rona, HD, Lowe's or a few lumber yards around town. Got a couple of other options I am looking into. Someone suggested Algonquin College as they have a woodworking program. Anyone ever been there?
    I got a fever. And the only prescription is more golf equipment.

  9. #9
    Need a Caddy jmwhite is on a distinguished road jmwhite's Avatar
    Join Date
    Jul 2012
    Location
    Gatineau
    Posts
    478
    Try the Wood Source in Manotick.

  10. #10
    Fairway Junkie sharkshooter is on a distinguished road sharkshooter's Avatar
    Join Date
    May 2005
    Location
    Ottawa
    Posts
    600
    Are you looking for a place to buy it as well?

    You could try Adams and Kennedy:

    Hours of Operation:
    Weekdays 7:30am-5pm
    Saturday 8am – 12 Noon


    6178 Mitch Owens Rd,
    P.O. Box 700
    Manotick, Ontario, Canada
    K4M 1A6
    Tel: 613.822.6800
    Toll Free: 855.822.6800
    Fax: 613.822.6803
    Email: info@wood-source.com

  11. #11
    Fairway Junkie sharkshooter is on a distinguished road sharkshooter's Avatar
    Join Date
    May 2005
    Location
    Ottawa
    Posts
    600
    Quote Originally Posted by jmwhite View Post
    Try the Wood Source in Manotick.
    snap

  12. #12
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    lol...I am buying the wood from the wood source. They don't have any means other than a chain saw to cut it...
    I got a fever. And the only prescription is more golf equipment.

  13. #13
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    these guys look promising, though he will have to do two cuts on a chop saw.

    http://www.woodselect.ca/en/Contact_us_18.html
    I got a fever. And the only prescription is more golf equipment.

  14. #14
    Singles Match Play Champ 2011 John is on a distinguished road John's Avatar
    Join Date
    Nov 2002
    Location
    Ottawa
    Posts
    6,202
    What size is your mitre saw at home? If it's a 12" that slides you should be able to make it work and might just have to finish with a hand saw?

  15. #15
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    Quote Originally Posted by John View Post
    What size is your mitre saw at home? If it's a 12" that slides you should be able to make it work and might just have to finish with a hand saw?
    12" non sliding. I could make it work but Pierre at wood select can likely source the wood, dress it and cut it for me which saves me the hassel. I think he has a jumbo band saw which would do the trick as well but would love to see the quality of the cut from that.
    I got a fever. And the only prescription is more golf equipment.

  16. #16
    Eagle Rusty is on a distinguished road Rusty's Avatar
    Join Date
    Aug 2001
    Location
    Rockland
    Posts
    350
    Wood Select did excellent work for me a few years back. Trimmed some huge walnut boards for me and did a very good job.

  17. #17
    Hall of Fame jeffc is on a distinguished road jeffc's Avatar
    Join Date
    Jun 2001
    Location
    In the 613!
    Posts
    8,315
    Quote Originally Posted by Rusty View Post
    Wood Select did excellent work for me a few years back. Trimmed some huge walnut boards for me and did a very good job.
    good to hear...Pierre seems like a great guy after talking to him
    I got a fever. And the only prescription is more golf equipment.

  18. #18
    Putter bestcircular is on a distinguished road
    Join Date
    Apr 2019
    Location
    PHILADELPHIA
    Posts
    1
    Who has been able to pick out the best product among those listed on this site? https://bestcircularsawreviews.com/

  19. #19
    Putter Samuel_Rice is on a distinguished road
    Join Date
    Apr 2019
    Location
    Montgomery
    Posts
    2
    This is a rather large procurement, so I don’t know who you could provide such a tool for use. Honestly, it would be better to buy such a saw for the future, I am sure that you will need it again and again.
    Last edited by Samuel_Rice; 04-27-2019 at 03:17 PM.

  20. #20
    Postmaster General big mac is on a distinguished road big mac's Avatar
    Join Date
    Feb 2004
    Location
    Home-and glad to be
    Posts
    3,821
    Stay away from the cordless unless you are somewhere where you have no power. The Dewalt is the same as Porter Cable. I have used mine for almost 40 years (Porter Cable/Rockwell) 15 amp motor and corded. Purchase a good set of blades---rip and crosscut and take care of the tool and don't tackle a job it was not intended to do. The use of a proper size extension cord also helps--don't use 16 or 14 gauge---12/3 will deliver proper current. A good clamp on guide to aid in ripping and cross cutting is also a good practice to follow.
    Does the 2nd hole-n-one come easier ?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. Adams Speedline F11 3 Wood Matrix XCON 7.1 "NEW"
    By mr. chopper in forum Right Hand Woods
    Replies: 2
    Last Post: 11-19-2012, 02:56 PM
  2. 2010 Adams Speedline Fast 3 wood "MINT"
    By mr. chopper in forum Right Hand Woods
    Replies: 0
    Last Post: 05-31-2010, 09:43 AM
  3. Callaway FT Tour 3 wood and FT Hybrids "MINT"
    By mr. chopper in forum Right Hand Woods
    Replies: 2
    Last Post: 08-31-2008, 07:18 AM
  4. Replies: 0
    Last Post: 01-02-2006, 11:37 PM
  5. A "One-Piece" Takeaway Is Essential
    By Kilroy in forum Instruction
    Replies: 0
    Last Post: 06-25-2005, 09:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts