+ Reply to Thread
Results 1 to 20 of 20
-
11-19-2012 04:29 PM #1
anyone have a big saw able to cut an 8x8" piece of wood?
I'm making a table and need to cut some pieces of douglas fir that are just under 8x8". I can do it with a couple of cuts on my mitre saw but was wondering if anyone had a bigger saw at home that would do this (e.g. radial arm saw), etc.
thanksI got a fever. And the only prescription is more golf equipment.
-
11-20-2012 12:26 PM #2
Jeff---are you crosscutting or ripping ? Bandsaw will do if you find a big one. Pretty hard to crosscut as the throat on most saws are 14 or 20 inches. If your ripping then anyone with a portable bandsaw mill can do it.
Ever tried to use a handsaw ??A good sharp one will work
Does the 2nd hole-n-one come easier ?
-
11-20-2012 12:35 PM #3
I am cross cutting it. I need the cut to be pretty exact and want to do minimal sanding. Don't want to do it by hand for accuracy reasons and the number of cuts required.
I got a fever. And the only prescription is more golf equipment.
-
11-20-2012 12:59 PM #4
- Join Date
- Nov 2007
- Location
- around here
- Posts
- 2,110
-
11-20-2012 01:03 PM #5
-
11-20-2012 03:28 PM #6
They will definitely do the cuts for you even if you didn't buy it there Jeff, i do it all the time. Don't waste your time at HD either go to Rona, the Cut Shop is far superior. Let's see some pics of this sucker once completed!
-
11-20-2012 07:57 PM #7
Rona has a huge table saw, they are much better in their cut shop then Home Depot.
Rona all the way for cuts.Obviously you're not a golfer.
-
11-21-2012 09:21 AM #8
so no luck with Rona, HD, Lowe's or a few lumber yards around town. Got a couple of other options I am looking into. Someone suggested Algonquin College as they have a woodworking program. Anyone ever been there?
I got a fever. And the only prescription is more golf equipment.
-
11-21-2012 09:29 AM #9
-
11-21-2012 09:31 AM #10
Are you looking for a place to buy it as well?
You could try Adams and Kennedy:
Hours of Operation:
Weekdays 7:30am-5pm
Saturday 8am – 12 Noon
6178 Mitch Owens Rd,
P.O. Box 700
Manotick, Ontario, Canada
K4M 1A6
Tel: 613.822.6800
Toll Free: 855.822.6800
Fax: 613.822.6803
Email: info@wood-source.com
-
11-21-2012 09:31 AM #11
-
11-21-2012 09:33 AM #12
lol...I am buying the wood from the wood source. They don't have any means other than a chain saw to cut it...
I got a fever. And the only prescription is more golf equipment.
-
11-21-2012 09:34 AM #13
these guys look promising, though he will have to do two cuts on a chop saw.
http://www.woodselect.ca/en/Contact_us_18.htmlI got a fever. And the only prescription is more golf equipment.
-
11-21-2012 11:22 AM #14
What size is your mitre saw at home? If it's a 12" that slides you should be able to make it work and might just have to finish with a hand saw?
-
11-21-2012 11:32 AM #15I got a fever. And the only prescription is more golf equipment.
-
11-21-2012 03:22 PM #16
Wood Select did excellent work for me a few years back. Trimmed some huge walnut boards for me and did a very good job.
-
11-21-2012 03:27 PM #17
-
04-23-2019 10:21 AM #18
- Join Date
- Apr 2019
- Location
- PHILADELPHIA
- Posts
- 1
Who has been able to pick out the best product among those listed on this site? https://bestcircularsawreviews.com/
-
04-26-2019 06:55 AM #19
- Join Date
- Apr 2019
- Location
- Montgomery
- Posts
- 2
This is a rather large procurement, so I don’t know who you could provide such a tool for use. Honestly, it would be better to buy such a saw for the future, I am sure that you will need it again and again.
Last edited by Samuel_Rice; 04-27-2019 at 02:17 PM.
-
04-27-2019 11:15 AM #20
Stay away from the cordless unless you are somewhere where you have no power. The Dewalt is the same as Porter Cable. I have used mine for almost 40 years (Porter Cable/Rockwell) 15 amp motor and corded. Purchase a good set of blades---rip and crosscut and take care of the tool and don't tackle a job it was not intended to do. The use of a proper size extension cord also helps--don't use 16 or 14 gauge---12/3 will deliver proper current. A good clamp on guide to aid in ripping and cross cutting is also a good practice to follow.
Does the 2nd hole-n-one come easier ?
Thread Information
Users Browsing this Thread
There are currently 2 users browsing this thread. (0 members and 2 guests)
Similar Threads
-
Adams Speedline F11 3 Wood Matrix XCON 7.1 "NEW"
By mr. chopper in forum Right Hand WoodsReplies: 2Last Post: 11-19-2012, 01:56 PM -
2010 Adams Speedline Fast 3 wood "MINT"
By mr. chopper in forum Right Hand WoodsReplies: 0Last Post: 05-31-2010, 08:43 AM -
Callaway FT Tour 3 wood and FT Hybrids "MINT"
By mr. chopper in forum Right Hand WoodsReplies: 2Last Post: 08-31-2008, 06:18 AM -
FS: Matby Xtreme 24° Utility Wood / UST IROD shaft "S"
By 93LE in forum Right Hand SetsReplies: 0Last Post: 01-02-2006, 10:37 PM -
A "One-Piece" Takeaway Is Essential
By Kilroy in forum InstructionReplies: 0Last Post: 06-25-2005, 08:09 AM