+ Reply to Thread
Results 1 to 14 of 14
Thread: garage door opener
-
01-31-2011 09:30 PM #1
- Join Date
- Apr 2009
- Location
- greenville
- Posts
- 65
garage door opener
helppp guys my garage door opener has got to be raised up some.......can someone tell me if this is possible??
-
02-01-2011 09:32 AM #2
what's the problem? is it stuck? is there an automatic opener on it? a few more details please.
if its stuck and there is an auto door opener, then you will need to pull the red handle (that's what mine has -its from sears) and that will unlock the mechanism and allow it to open.
also, if you want to "lock" it from then inside and the opener is disengaged, just put a set of vice grips on the rail so the wheels can't move.I got a fever. And the only prescription is more golf equipment.
-
02-01-2011 09:51 AM #3
Garage Door Opener
Bubba827
If you are wanting to raise your garage door opener i believe the only way to do this properly is to change the tracks that the door runs on, the door tracks and the sprocket of the motor in the door opener must be parallel. You could possibly flip the opener upside down but you would have to reverse the motor operation and im not sure if there is enough tension on the chain to keep it on the sprocket or if the motor will run properly in that orientation. Flipping the opener would give you about another 10-12 inches clearence though.
Hope this helps.Smooth it out there!!!!
-
02-01-2011 10:39 AM #4
- Join Date
- Aug 2010
- Location
- Zionsville
- Posts
- 6
Bubba827,
You may want to look at another option, depending on your budget.
http://www.liftmaster.com/consumerwe...px?modelId=834
I got this jackshaft garage door opener which attaches to the torsion bar on the side, so it completely opens up your garage ceiling space. It's a heck of a lot quieter than my old garage door opener, but maybe that's because it was 27 years old. It cost me $500 USD to buy the new one and have it installed. If you're more mechanically inclined than I am (and that wouldn't take much) you could obviously save some bucks by installing it yourself.
-
02-01-2011 10:42 AM #5
- Join Date
- Jan 2011
- Location
- Alberta
- Posts
- 356
-
02-01-2011 04:49 PM #6
- Join Date
- Apr 2009
- Location
- greenville
- Posts
- 65
srry for the lack of info guys..but yes I am trying to hook up my DD sim and i have 3 walls to use and I will be dang gone if that blasted thing is in the way no matter which wall i try....I did some testing before i bought projector and screen and all the pieces to hook it up with but must have been drinkin the night i checked for cleareance purposes.......lol....I only need about 6 or 7 inches ........was wondering if I were to raise up the motor and then track bar if that would change the angle too much and put too much tension on my mounting bracket..............i called my local company and before i could get everything out of my mouth she said no there is no way to do it.....just asking here for advice on this matter....thx guys
-
02-01-2011 05:04 PM #7
- Join Date
- Oct 2010
- Location
- Chicago
- Posts
- 3,687
6 or 7 inches should be doable. At the risk of offending women all over the internet, you should call another installer and ask a guy that question.
Post some pictures of what you have to deal with.
I looked at mine and I can definitely raise it if I have to. On mine the arm(from the track) that attaches to the door can be extended.
-
02-01-2011 05:25 PM #8
- Join Date
- Jan 2011
- Location
- Alberta
- Posts
- 356
Just looked at my opener on my door and my bar is already at an angle and the bar attached to the door is on a piviot so in my case I don't think it would matter if the glide bar was raised up a bit higher. In my case the opener motor is already close too the ceiling. There is not a lot of weight pulling on that motor as most of it is on the spring load so as long as the bar that connects to the door is on a piviot I think you might be ok.
-
02-01-2011 06:14 PM #9
- Join Date
- Apr 2009
- Location
- greenville
- Posts
- 65
thanks guys i also have some extra space that I can extend the arm out some....I will try this hopefully in the next couple days and also will post some pics of before and after....thanks again guys
Oh almost forgot the reason I was asking this is a friend of mine also moved his garage opener up and he felt that because the angle of the arm changed that it put extra strain on his motor and the gears on it stripped out after about 1 month of use.....
-
02-01-2011 07:34 PM #10
I have a Chamberlin garage door opener with a belt drive. Would I be able to extend the motor another 4 feet, (which is the distance that comes with a standard section of the arm/rail that guides the pull mechanism? Can an extra length belt be obtained for this extension/modification?
Moving the motor head another 4 feet away from the garage door would provide an area for left handed players without having to switch the position of the simulator
Thanks.Engineered Golf - Frank Hann 3.8 GHIN
www.engineeredgolf.ca
-
02-02-2011 07:55 AM #11
- Join Date
- Mar 2010
- Location
- Louisville
- Posts
- 30
The term you are looking for is high lift garage door. That's the most useful link at a glance from Google, but there are probably more.
Bubba, your friend probably didn't adjust his torsion spring, so the opener did have to take up the extra lift.
-
02-03-2011 11:43 PM #12
- Join Date
- Mar 2010
- Location
- Louisville
- Posts
- 33
I say forget left handed golfers...all they do is case me problems... Looking at you jacky!
-
02-04-2011 09:29 PM #13
- Join Date
- Apr 2009
- Location
- greenville
- Posts
- 65
whoaaaaaaaaaaaaaaaaaaaaaaaaaaa there now I am a lefty here also...............lol
-
02-05-2011 02:41 PM #14
- Join Date
- May 2010
- Location
- Bay Shore, NY
- Posts
- 115
You can have a "high lift kit" put in. You keep your current opener and door, but it raises the track up and adds new springs. I did this, I contacted a local garage door company to come do it. It raised the height of the garage door and tracks to 10 feet tall. The cost was $600 (here in New York anyways).
Thread Information
Users Browsing this Thread
There are currently 4 users browsing this thread. (0 members and 4 guests)
Similar Threads
-
Garage Door Remote
By jsttaylor in forum Other StuffReplies: 0Last Post: 02-01-2011, 09:57 AM -
RDH, how did you mount projector behind the garage opener?
By dvshx in forum Home Simulators - HardwareReplies: 10Last Post: 10-07-2010, 01:30 AM -
Door Opener
By Felix in forum Business NetworkingReplies: 10Last Post: 11-09-2009, 05:54 PM -
garage door openers
By jeffc in forum Almost AnythingReplies: 4Last Post: 03-09-2009, 10:32 AM -
Garage door opener
By downhillslider in forum Other StuffReplies: 0Last Post: 03-05-2009, 09:29 AM