+ Reply to Thread
Results 1 to 9 of 9
Thread: hybrid shaft length?
-
04-12-2007 10:55 PM #1
- Join Date
- Apr 2007
- Location
- Brandon, MB
- Posts
- 8
hybrid shaft length?
Hi. I'm building two hybrids and can't seem to find any standard advice on shaft length for hybrids. The heads are Makser AS40, which have .370 hosel. I have UST Irod hybrid shafts in stiff. I assume no need to tip trim, since the shafts are designed for hybrids. However, I can't decide on the proper length. The Makser website shows these as built to 39.5" for 21deg head and 39" for 24deg head. But I don't know what shafts they would be using for factory built clubs. Golfsmith, on the other hand, suggests 41" and 40.5" respectively for graphite shaft hybrids at these lofts. I'm guessing that Golfsmith suggests longer clubs because they are, I think, assuming .335 tip shafts, and are spec'ing for proper launch on that basis. I'm partly wondering if the Makser specs are different due to the .370 tip. If it helps, the heads both have 60deg lies. Should I go with the Makser specs? Thanks for any input! supercustom
-
04-12-2007 11:09 PM #2
- Join Date
- Apr 2007
- Location
- Brandon, MB
- Posts
- 8
At risk of going on... I should add it's a standard bore head, so not much of the shaft goes into the hosel.
-
04-13-2007 06:40 AM #3
Do not assume that because it is a hybrid shaft that it is not made to be tip trimmed. Check the trimming instructions first,
Most companies will suggest various lengths mostly because of a target swingweight. I for myself will match the length with the equivalent weight of an iron. But if swingweight is not an issue and if in no hurry try the following; after the heads have been glued do not put the grips on permantly. Slit a grip(remove the cap as well) and head to the range with impact decals and masking tape(or a lie board if you have one). This way you can try different length combinations by sliding the grip up and down until you hit your target i.e the proper lie and length for YOU and centre face contacts. Once you hit your target mark the shaft with a marker and cut it there.Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
04-13-2007 07:43 AM #4
-
04-13-2007 08:35 AM #5Don't mean to be editing you post Andre but did you mean to say equivalent length?Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
04-13-2007 10:47 AM #6
- Join Date
- Apr 2007
- Location
- Brandon, MB
- Posts
- 8
Thanks for the tip on the driving range experiment. On tip trimming, I've seen this shaft listed on Golfsmith with instructions only to butt trim to length. I play my irons +1/2" so I'm inclined to try longer first, then go shorter if my game demands it. I just wanted advice on the discrepancy which I wasn't sure if was due to the lie angle of these particular heads. But as you say, regardless of that, I need to fit to MY game.
-
04-13-2007 04:49 PM #7
I would double check if I were you:
http://www.golfsmith.com/cm/trim.php
Shaft Brand:UST Shaft Name:IROD Hybrid Long Iron Shaft Stock Number:3898i Category:Graphite Iron Shafts
Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
04-15-2007 01:45 AM #8
- Join Date
- Apr 2007
- Location
- Brandon, MB
- Posts
- 8
Wow, don't know how I missed that. OK, the shaft I have is the Irod hybrid long iron (Golfsmith stock# 3898i). The guide at Golfsmith lists tip trimming for irons (2 to 5). Since I'm using the shaft for a true hybrid head, do I go with the equivalent iron it's replacing for the tip trim? Or am I just asking for trouble trying to use this shaft in a hybrid head? Thanks again for the (so far) helpful advice.
-
04-15-2007 10:23 AM #9
Just go with the equivalent weight in an iron i.e if the hybrid head is 240 grams use the tip trim for a 3 iron and so on. You will notice that most hybrid heads weigh just about the same of the iron head it is supposed to replace.
Hope this helps.Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Shaft length for 3 wood and hybrid?
By pengki in forum Club Making & ComponentsReplies: 5Last Post: 02-29-2012, 10:30 PM -
Shaft length?
By BG458 in forum Club Making & ComponentsReplies: 4Last Post: 09-21-2008, 07:12 AM -
shaft length
By shank13 in forum Club Making & ComponentsReplies: 3Last Post: 03-21-2008, 03:12 PM -
Hybrid length
By covanant in forum Club Making & ComponentsReplies: 11Last Post: 11-02-2006, 06:16 PM -
hybrid shaft length for 3 iron
By carson city in forum Club Making & ComponentsReplies: 2Last Post: 06-17-2005, 09:45 PM