Royal precision Rifle Iron shafts

[rezadue]

I have a set of (3-PW) Rifle 6.0 shafts pulled from my RAC LTs for sale. These shafts have a one inch butt extension which can easily be cut down if you want standard length.

Asking $60 o.b.o

Would be willing to trade for a hybrid shaft as well.

[Wayne]

I need a 5.0 rifle shatf, can you pull out the 5.0 from your Tm RAC? I will take it if they are 0.355.



Thanks

[rezadue]

The RAC LTs were sold with the rifle 5.0s. I believe the 6.0s are 0.370" diameter.

[Wayne]

Thanks

[rockford35]

Rez,

Let me know if those 6.0's are in fact .370.

Thanks,

R35

[rezadue]

These came out of my RAC LTs and according to what I found on the net RAC LTs are 0.370".

[rezadue]

Now $55 or best offer. And I am open to trades too. Let me know what you have?

[petah]

Do you know if these shafts will fit into callaway X16 irons? The callys are bore through.

Thanks.

[rezadue]

No idea. If they do fit, I suspect that you would probably not need to cut anything off to play at standard length though. However, they will probably play more stiff than a Rifle 6.0

Club making gurus can correct the above statement if I am wrong.

[downhillslider]

No idea. If they do fit, I suspect that you would probably not need to cut anything off to play at standard length though. However, they will probably play more stiff than a Rifle 6.0

Club making gurus can correct the above statement if I am wrong.

Not so. Cally irons have the same distance from the bottom of the bore to the ground as most all irons do. Therefore, they will play as 6's, depending on what lenght you choose. Yes, they will fit but be fowarned. This is not a standard installation technique.

[goto10]

Not so. Cally irons have the same distance from the bottom of the bore to the ground as most all irons do. Therefore, they will play as 6's, depending on what lenght you choose. Yes, they will fit but be fowarned. This is not a standard installation technique.

huh? The Cally's are X-16 bore throughs. BBGM = 0

[Chieflongtee]

No idea. If they do fit, I suspect that you would probably not need to cut anything off to play at standard length though. However, they will probably play more stiff than a Rifle 6.0

Club making gurus can correct the above statement if I am wrong.

They will fit and they will play close to standard length since they have been extended 1 inch to begin with. However you will have to take these to someone who knows what they are doing. The shafts will have to be slit or the hosels will have to be reamed to .370. Shaft plugs will have to be installed and the shaft tips will have to be cut or nylon wheel polished at a 45 degree angle.

[Chieflongtee]

huh? The Cally's are X-16 bore throughs. BBGM = 0

I believe he meant that they are not going to play much softer or stiffer since the cally hosel is so short even though it's a bore through hosel. Slider knows his stuff.

[goto10]

I wasn't commenting on whether or not they play stiffer, just that they DO NOT have 'the same BBGM as most irons do'.

[Chieflongtee]

I wasn't commenting on whether or not they play stiffer, just that they DO NOT have 'the same BBGM as most irons do'.

10-4. since we're on the topic wouldn't you say that the bbgm is 1/8 or so since the sole has a radius

[goto10]

lol got me there Nordique.

[rezadue]

Al of this is all good. But does anyone want to buy my shafts?

[downhillslider]

huh? The Cally's are X-16 bore throughs. BBGM = 0

0 BBGM means that the shaft touches the ground. So, you are saying that it does ? Better check again

[downhillslider]

I believe he meant that they are not going to play much softer or stiffer since the cally hosel is so short even though it's a bore through hosel. Slider knows his stuff.

You are to kind Chiefy !

[goto10]

LOL... Ya got me! 1/8" in this case? 1/4"?

Cally irons have the same distance from the bottom of the bore to the ground as most all irons do.

So most irons have a 1/4" BBGM? In your words, 'Better check again'.

[rockford35]

Rez,

PM sent on the Rifles. For real.

No, seriously!

R35

[rezadue]

PM replied. Lets git'er done.

[rezadue]

$45.

[scanner_66]

are those shafts still for sale? what was used to do the extensions?

Geoff

[rezadue]

Yes they are available. I am not sure what the material is. It looks like steel. But they can be cut back to original if you so desired.

And just for clarification, the extension is at the butt of the shaft which means it is covered by the grip.

[scanner_66]

pm sent

[rezadue]

PM Replied.

[scanner_66]

Rez, as per my pm, I apolagize for the inconvienience, I just can't do it right now.

Sorry

Geoff

[rezadue]

Would be willing to trade for a hybrid shaft for my Nickent 3DX 3h.

[downhillslider]

Fuji Banzai for the 6.0's Let's do it !