+ Reply to Thread
Results 1 to 8 of 8
Thread: Question about Cleveland wedges
-
08-29-2006 01:15 PM #1
Question about Cleveland wedges
Do they make Tour Action 588 wedges in the satin finish? I would love to get a 52 and a 60 to go with my irons, but am wondering if they even make them.
-
08-29-2006 01:29 PM #2
- Join Date
- Feb 2005
- Location
- Forever stuck between single digit and trunk slammer!
- Posts
- 16,809
Yes, but very rare. They are called TSC (Tour Satin Chrome). I wish you good luck in that search.
"A life lived in fear of the new and the untried is not a life lived to its fullest." M.Pare 10/09/08
-
08-29-2006 01:34 PM #3
- Join Date
- Mar 2002
- Location
- Almonte, Ontario
- Posts
- 584
And I guess that makes me the lucky owner of a couple of them. I didn't know they were rare though.
nice_lag
Almonte
-
08-29-2006 01:39 PM #4
-
08-29-2006 01:44 PM #5
They're not that rare John, only rare when compared to other Cleveland models which are made by the millions.
In fact when your set of 588 blades came out they made satin 588 wedges to match.The opinions expressed in this post are mine and may not necessarily reflect the opinions of others on OG.
-
08-29-2006 01:50 PM #6
- Join Date
- Feb 2005
- Location
- Forever stuck between single digit and trunk slammer!
- Posts
- 16,809
Reid is correct and I should have explained better. Did not mean to imply they are impossible to come by but much more rare than the regular wedges that are massed produced like Reid said.
But also it seems like people are not always eager to part with them. So they must be good!"A life lived in fear of the new and the untried is not a life lived to its fullest." M.Pare 10/09/08
-
08-29-2006 02:10 PM #7
Ya, I actually found a couple on ebay...60 degree didn't look like it was in very nice shape though, and the 53 was a a lefty. I know that a 51 degree can be bent to 52, but is it possible to bend a 53 back to 52?
-
08-29-2006 02:23 PM #8
- Join Date
- Feb 2005
- Location
- Forever stuck between single digit and trunk slammer!
- Posts
- 16,809
Shouldn't be a problem. Its when you start to try to bend cast clubs more than 3 or 4 degrees that problems arise.
"A life lived in fear of the new and the untried is not a life lived to its fullest." M.Pare 10/09/08
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Cleveland ''diadic'' question.
By PatS in forum Golf ClubsReplies: 6Last Post: 01-02-2016, 03:36 PM -
FS: WEDGES - Cleveland 60* DSG 588 (Gunmetal) & Cleveland 54* SW TA reg.588 (Chrome)
By Scotty1225 in forum Right Hand IronsReplies: 1Last Post: 04-08-2011, 12:56 PM -
Cleveland Stock Shaft Question
By Chanter in forum Golf ClubsReplies: 0Last Post: 03-30-2009, 09:06 AM -
Cleveland Ta7 Tour Irons & Cleveland Wedges
By doctor-wedge in forum Right Hand SetsReplies: 8Last Post: 08-02-2007, 03:49 PM -
Cleveland 588 RTG Wedges
By Mayday in forum Right Hand SetsReplies: 2Last Post: 04-05-2005, 11:21 AM