+ Reply to Thread
Results 31 to 46 of 46
Thread: Back Weighting grips
-
12-20-2005 04:47 PM #31
Actually Denny you should check out Canadian Tire as they have a 3 gallon compressor on sale for $79. It comes with the tool you are refering to. I know I have one. As far as no tape it is only for Star Grips. When it comes to grip size tape is factored in the equation. One layer of masking tape will equal a standard size grip. I purchased a transparent tube and a kit from Arnie Schwartz for $24 and it is a lot better than any shaft tube out there. If you want to be on the safe side buy a piece of PVC. I still prefer the transparent tube as I can see the grip all the way through.
Last edited by Chieflongtee; 12-20-2005 at 05:27 PM.
Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
12-20-2005 05:00 PM #32Originally Posted by dbleber
You can find the Adaptor for about 4-5 dollars in just about any store that sells compressor.Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
12-20-2005 05:26 PM #33
http://www.myostrichgolf.com/clubmak...roducts_id=789
The Grip Blaster - Grip Installation and Removal Tool
Blow grips on and off with air!
The Grip Blaster is a high quality machined tool that includes an air blow gun for precise control of air to do the job. The Grip Blaster's specially designed fitting allows for easy installation and removal of both round and molded (putter) grips.
Using your compressor and The Grip Blaster, you can dramatically improve your ability to save and reuse grips - great for allowing a customer to test a specific grip on his club in your shop!
Most grips can be safely removed in one piece with the proper application of air and a little solvent. Thin grips like Callaway grips, some wrapped grips and old or dried grips may not come off without being damaged. With practice, your success rate will go up, so don't give up!
Grips can be installed without grip tape - however grip tape can also be used for a more secure installation. Masking tape may be required for proper grip sizing even if grip tape is not used.
Installing Grips with Air
Clamp the golf shaft in an appropriate vise
Size the grip (using build-up tape as necessary), and apply double-sided grip tape or masking tape to the shaft butt
Dip the mouth of the grip in grip solvent - wetting the first 1/2" or so.
Slide grip onto the shaft about 1/2"
Place The Grip Blaster over the butt end of the grip, inserting the nossle tip into the grip air vent.
Holding the grip near the butt, gently apply air while sliding the grip on - keeping The Grip Blaster firmly pressed against the grip butt.
Short blasts of air may be applied to aid in aligning the grip once installed.
Removing Grips with Air
Clamp the golf shaft in an appropriate vise
Puncture any grip tape covering the end of the shaft butt by sliding an awl into the grip vent hole. Remove the awl.
Slide the Safety Tube over the grip, aligning the end with the grip butt
Place The Grip Blaster into the vent hole of the grip, and apply a blast of air
The grip will expand into the Safety Tube, which helps prevent the grip from exploding - though some may still explode or split. Remove these grips with a standard hooked knife.
If the first blast of air does not free the grip, squirt a small amount of grip solvent into the vent hole and repeat
If the grip "pops" and partially releases from the shaft, you may wish to remove the Safety Tube and assist removal by twisting the grip while applying air pressure. Many grips will simply slide free in one motion without assistance.
Grips with underlistings may be removed by twisting the grip during the careful application of air. It takes some finesse, some solvent, and some luck, but even expensive, leather slip-on wraps can be safely removed and reused with The Grip Blaster.
Includes one Grip Blaster and one Safety Tube.Last edited by Chieflongtee; 12-20-2005 at 06:05 PM.
Live as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
12-20-2005 06:55 PM #34
Andre,
I already have a compressor but want to the adapter. I think I will just buy one from crapy tire and put a needle on it. I don't really see the point though if you have to tape it and use solvant. I guess for removing old grips but I know that when I got my Accra shaft at Artisan he put a Titleist cord grip on the shaft using an air compressor without any tape and it didn't move a bit. The whole point of an air compressor to me is to eliminate having to waste time and mess with tape and solvant. I try it and see how it works.
Thanks
-
12-20-2005 07:07 PM #35Originally Posted by dbleberLive as if you were to die tomorrow. Learn as if you were to live forever.
Mahatma Gandhi
-
12-20-2005 08:26 PM #36
I will, I did hear that the grips can kind of explode on you if your not careful. Hopefully I won't learn that the hard way!
-
12-21-2005 09:49 AM #37
About the nozzle. I just insert the pointed tip that it comes with into the hole in the grip and, no problems! Slides on and off easy. I STRONGLY recommend the use of a tube when removing!!! At least until the grip pops free the first time. After that you can wiggle the grip off with short blasts of air.
-
01-19-2006 12:00 PM #38
- Join Date
- Dec 2005
- Location
- Stittsville
- Posts
- 1,512
Originally Posted by clubfixer
-
01-19-2006 12:55 PM #39
There does not seem to be any pattern that can be tracked as to who this can help, or how much weight is the right amount, that I have seen. I had recently built a set, 5 through SW, for a guy who hit all of them well except the 5. I put 32 grams in a 5 iron and now he likes it? This guy has a relatively flat swing with a definite shoulder first, over the top move. I had noticed that the marks left from the mat on the sole of his club changed from the rear edge to the leading edge, not that I noticed him casting the club prior to back weighting. The shots were down the middle with an 8 yard average gain from the 6 iron. Not to bad for not being able to advance the ball prior to back-weighting.
[FONT=Comic Sans MS][COLOR=blue]Play it as it lies...[/COLOR][/FONT]
-
01-19-2006 02:38 PM #40
- Join Date
- Dec 2005
- Location
- Stittsville
- Posts
- 1,512
A 1 plane swinger might like it as opposed to a 2 planer ?
-
01-19-2006 02:40 PM #41
Or maybe it will turn a two plane swinger into more of a one planer...
[FONT=Comic Sans MS][COLOR=blue]Play it as it lies...[/COLOR][/FONT]
-
01-19-2006 04:07 PM #42
- Join Date
- Dec 2005
- Location
- Stittsville
- Posts
- 1,512
Also should mention that I did not have a problem feeling the clubhead with this swingwieght ( C4)
-
01-20-2006 08:37 PM #43
Same here. I could feel the hands more in the swing but not the added weight, or should I say the feel of where the head is during the swing.
[FONT=Comic Sans MS][COLOR=blue]Play it as it lies...[/COLOR][/FONT]
-
02-02-2006 10:26 AM #44
- Join Date
- Feb 2006
- Location
- New York State
- Posts
- 4
About Back-Weighting
After reading the responses to my inquiry, I think that many have some what missed the piont. The process of back-wieghting is not about making a shaft more Heavy. It IS about as one has said, the act of "fooling". I think it is an effect that increases Feel and is translated to hand action. I would like to keep the lines of communication open on this subject.
Thanks, Smellman
-
02-02-2006 11:53 AM #45
Smellman,
Here is a link from Balance Certified that has some pretty interesting test results on this subject.
http://www.balance-certified.com/pag.../11/19/0150711[FONT=Comic Sans MS][COLOR=blue]Play it as it lies...[/COLOR][/FONT]
-
02-02-2006 03:41 PM #46
- Join Date
- Feb 2006
- Location
- New York State
- Posts
- 4
Thank you! This is way cool! I like this application better because of the ability to use the grip type that you like as opposed to the C-Forse brand, Victory Velvet Grip.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Wtt new red golf pride ndmc grips for some white ndmc grips
By beef in forum Components & ToolsReplies: 2Last Post: 11-23-2011, 11:24 PM -
Tommy Armour Silver Scot forged cavity back or muscle back.
By nakkie in forum Golf ClubsReplies: 0Last Post: 05-22-2007, 03:09 PM -
Questions about Cavity back versus Muscle back irons
By guitarman in forum InstructionReplies: 23Last Post: 09-26-2006, 01:54 PM -
The Ultimate In Perimeter Weighting?
By LobWedge in forum Golf ClubsReplies: 6Last Post: 01-23-2006, 10:57 PM -
Counter-weighting?
By jvincent in forum General Golf TalkReplies: 0Last Post: 11-07-2005, 08:48 AM